37" x 103" Sanding Belt, 2 PACK Cloth Closed Coat A/O / 36 Grit
Add 2 more to save 10%.
Available in stock (49990)
Check return eligibility and fees
A 44-inch belt only 60 inches long belongs to a compact class of wide belt sander, and the Cantek C431 is the machine our original listing named for it. Short-loop machines like that run hot and hard because there is less belt to shed heat, so backing and coat matter more than usual. These 44" x 60" belts are closed-coat aluminum oxide on poly-cotton cloth, joined to run in either direction.
Aluminum oxide is the only grain we stock in this size, in 36 through 320 grit, two belts to a pack. That covers calibrating, surfacing and finishing on hardwood, plywood, MDF and veneer, plus aluminum and composites on machines set up for them. Zirconia or other lengths can be quoted as custom belts. Converted in Anaheim, California.
This size is stocked in one material, so the choice is which grit rather than which grain.
Our original page put the open-coat question simply: are you sanding a very soft, pitchy softwood? Almost always no, in which case closed coat cuts faster, lasts longer and is the only choice for metal. If you calibrate dense hardwood or steel all day and want zirconia, we can convert it in this size as a custom belt; it is not a stocked option in 44" x 60".
| Grit | Use it for | Notes |
|---|---|---|
| 36 | Calibrating rough or glued-up stock | 1/64" passes; keep the feed up |
| 60 | Thicknessing, levelling joints | Removes the 36 scratch |
| 80–100 | General surfacing | Typical first belt on planed stock |
| 120–150 | Pre-finish on hardwood, plywood, MDF | Platen if fitted |
| 180–220 | Final pass before stain or clear coat | Stop at 220 for stain |
| 320 | Sealer and primer flatting | Skim passes, light pressure |
Step no more than one grade at a time. This size skips 40 grit, so go 36 to 60, and skips 400, so 320 is the finest flatting pass available.
Match both numbers. We also stock 43" x 60" and 44" x 75" belts, and neither substitutes for this one: an inch of width overhangs or under-covers the drum and misses the tracking sensor, and most machines accept only about a quarter inch of length variation. These belts run bi-directionally; inspect the joint tape before mounting. Other 44-inch lengths are converted as custom belts in about 3 days.
For joint failures and breakage see our guide to why wide sanding belts break. For ripple and chatter marks see the woodworking chatter Q&A.
Use it for
Don't use it for
| Size | 44" x 60" |
|---|---|
| Abrasive grain | Aluminum oxide |
| Backing | Poly-cotton cloth |
| Coat | Closed |
| Joint | Bi-directional |
| Grits offered | 36, 60, 80, 100, 120, 150, 180, 220, 320 |
| Pack quantity | 2 belts, one grit per pack |
| Machine type | Cantek C431 and other compact 44-inch wide belt sanders |
| Converted in | Anaheim, California |
| Custom sizes and grains | Any width, length or grain, about 3 days |
The Cantek C431 is the machine our original listing named for the 44" x 60" size. Confirm the size plate or manual on your machine before ordering, since belt lengths vary between models. If your plate shows a different length or width, we convert custom belts to match in about 3 days.
This size is stocked in closed-coat aluminum oxide only, which covers wood, panel products, aluminum and composites well. Shops that calibrate dense hardwood or steel and want zirconia can have it converted as a custom 44" x 60" belt; call 714-646-3299 or email sales@maverickabrasives.com for a quote.
No. An inch of width matters on a wide belt sander because the belt has to cover the drum and pass the tracking sensors at both edges. A 44-inch belt overhangs a 43-inch drum; a 43-inch belt leaves a 44-inch drum uncovered. We stock both as separate listings, so order the width on your machine plate.
For planed hardwood and plywood doors, 80 and 120 grit take out knife marks and prepare for finish, with 180 as the last pass before stain. Add 36 or 60 if you calibrate glued-up panels, and 320 if you flat sealer on the machine. Keep each step within one grade of the last.
A 60-inch loop passes over the drum far more often per minute than a 103-inch or longer belt, so each section of cloth has less time to cool and shed dust between cuts. Take lighter passes, keep the conveyor moving, run strong extraction, and clean the belt with a crepe eraser before it glazes.
Each pack holds two 44" x 60" belts of one grit; grits are not mixed within a pack. Orders over $200 ship free, unused belts in original packaging can be returned within 30 days, and case pricing or standing orders can be arranged by calling 714-646-3299 or emailing sales@maverickabrasives.com.
Couldn't load pickup availability
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.